ProStart CT-3371 Guia de Instalação descarregar pdf

4-BUTTON 1-WAY AUTOMATIC/MANUAL

TRANSMISSION REMOTE STARTER WITH

VIRTUAL TACH SYSTEM (AS PRG-1000

COMPATIBLE)

Notice

The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, be that either

damage to the vehicle itself or to the unit. This unit must be installed by a certified technician using all safety devices supplied. Please

note that this guide has been written for properly trained Autostart technicians: a certain level of skills and knowledge is therefore

assumed. Please review the installation guide carefully before beginning any work.

Warning

Before installing the unit, if installing on a vehicle with a manual transmission, test that the OEM Door Switch contacts of the vehicle work

well, and that the Parking Brake system operates properly. If installing on a vehicle with an automatic transmission, test that the vehicle

does not start when the gearshift lever is in the “Drive” position. If it starts in gear, reset the remote starter to manual transmission.

QUICK INSTALLATION GUIDE

To obtain a copy of the installation guide, please visit our website at www.prostart.org

TableofContents

Manual or Automatic Transmission setup 1

NEW FEATURE – Push To Start 2

NEW FEATURE – Hybrid Option 2

Entering Programming Mode 2

Programming the transmitter to the module 3

Entering Programming Options 3

Programming Options 3

Horn adjustment 4

Setting up the TACH 5

Virtual Tach adjustment 5

Multi-speed Tach Programming (if installed) 5

Transponder Programming 5

Resetting the Module 5

Bypass 5

NEW FEATURE – SmartStart™ 6

Testing 6

Diagnostics – Parking Light Flash Table 7

Diagnostic table for start failure. 7

Diagnostic table for shutdown. 7

The wiring diagram is at the middle of this guide.

MANUAL OR AUTOMATIC TRANSMISSION SETUP

This module may be installed on vehicles with manual or automatic transmissions. It is originally configured for

manual transmissions. If the vehicle you are working on is automatic, it is necessary to make a few quick and

easy modifications before the unit is connected. In the event that the configuration requires changes afterwards,

a complete reset will be necessary before those changes become effective.

To install this unit in a vehicle with a MANUAL transmission:

1. Make sure the Yellow loop on the PC board is connected. (Default)

2. Connect the Orange handbrake wire, located on the 12-pin harness, to the vehicle handbrake

switch. (-)

3. Connect the Blue/White (+) door input OR the Grey (-) door input wire, located on the 12-pin

harness, to the vehicle door pin wire. It will monitor all the doors of the vehicle (only use 1 of the 2

door trigger inputs).

4. Make sure the Purple TACH wire is installed on a TACH source – the TACH wire MUST be hooked

up when the module is set for a manual transmission.

5. Make all your regular connections.

6. Power up the unit by first inserting the 5-pin connector, then the 6-pin connector and finally the 12-

pin connector. The parking lights will flash 4 times.

7. When learning the transmitter, the parking lights will flash 5 times quickly.

8. Upon the first successful remote start, the system will lock the transmission settings to manual

mode.

To install this unit in a vehicle with an AUTOMATIC transmission:

1. Cut the loop on the back of the remote starter module (Yellow wire).

2. Make sure the Orange handbrake wire is not connected to any of the vehicle circuits (cut and

tape).

3. Make all the regular connections.

4. Power up the unit by first inserting the 5-pin connector, then the 6-pin connector and finally the 12-

pin connector. The parking lights will flash 4 times.

5. When learning the first transmitter, the parking lights will flash 5 times quickly then give 2 slow

flashes.

6. Upon the first successful remote start, the system will lock the transmission settings to automatic

mode.

1 2 3 4 5 6

Resumo do Conteúdo

Página 1 - QUICK INSTALLATION GUIDE

4-BUTTON 1-WAY AUTOMATIC/MANUAL TRANSMISSION REMOTE STARTER WITH VIRTUAL TACH SYSTEM (AS PRG-1000 COMPATIBLE)Notice The manufacturer will accept no re

Página 2 - ENTERING PROGRAMMING MODE

P.2 http://www.prostart.org Quick Installation Guide Note: If upon pressing the START/STOP button the parking lights give 3 slow flashes, make sure

Página 3 - ENTERING PROGRAMMING OPTIONS

Quick installation Guide http://www.prostart.org P.3 PROGRAMMING THE TRANSMITTER TO THE MODULE 1. In programming mode (page 3) - the parking lights

Página 4 - HORN ADJUSTMENT

Quick installation Guide http://www.prostart.org P.7  Parking brake shutdown circuit (for manual vehicles only). With the vehicle running under rem

Página 5 - VIRTUAL TACH ADJUSTMENT

Quick installation Guide http://www.prostart.org P.5 5. To save the new settings: press LOCK and UNLOCK simultaneously. If 3 chirps are returned, th

Página 6 - WIRING SCHEMATIC

V2.01 SS - July 26, 2010 -TACH: HIGHTACH Threshold: NORMALProgrammingAssistance Button(P.A.B.)1. GRAY/LIGHT BLUE....(-) N/A 2. BLUE/WHITE.

Mais documentos para Sistemas de ignição com controlo remoto ProStart CT-3371

Para ver o documento ProStart CT-3371 Guia do Utilizador

ProStart CT-3371 Guia do Utilizador (12 páginas)

Para ver o documento ProStart CT-3371 Guia de Instalação

ProStart CT-3371 Guia de Instalação (30 páginas)

ProStart CT-3371 Guia de Instalação (2 páginas)

Comentários a estes Manuais

Sem comentários

ProStart CT-3371 Guia de Instalação

Consulte online ou descarregue Guia de Instalação para Sistemas de ignição com controlo remoto ProStart CT-3371. ProStart CT-3371 Installation guide Manual do Utilizador

Resumo do Conteúdo

Mais documentos para Sistemas de ignição com controlo remoto ProStart CT-3371

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de ignição com controlo remoto ProStart CT-3371